RM Logo
Technical Rating: 
Support Home PageSupport
Print This PagePrint This Page
Add to 'My Library' Add to 'My Library'
Forward to a ColleagueForward to a Colleague

USB device overcurrent status detected error message
Published Date : 25 Feb 2010   Last Updated : 24 Mar 2010   Content Ref: TEC1628410  





Symptoms

When you switch on the computer or connect a USB device, a BIOS message or Windows message may be displayed such as:

  • USB device overcurrent status detected
  • Error 0701: USB overcurrent error
  • USB Device error
  • USB Device not recognized (Windows)
  • Shutting down in 15 seconds


Cause

The most likely causes are:

  1. A mechanical issue with one or more USB ports (eg broken, shorted).
  2. A faulty USB peripheral is or has been connected to the USB port.
  3. A blown fuse on the motherboard caused by a faulty peripheral.
  4. A peripheral is or has been connected that required too much power (eg should be used with an AC adapter or connected to two USB ports on the computer).
If a USB plug is inserted into this socket, it will short out the 5V supply!
  A user damaged USB socket (note the plastic tongue is missing and the four contacts are shorting on the metal shroud)


Procedure

  1. Remove all USB peripherals (printers, keyboard, mouse, USB flash memory pens, etc) from the computer. Note that some RM Ones also have a USB Webcam - unplug this from the rear USB port.
  2. Examine all of the USB ports on the computer for damage. Check that the four gold contacts are not bent and that the plastic tongue is present and not broken.
  3. Switch off and unplug the system from the mains supply or AC adapter. Leave for a few minutes and try again. If the same problem exists them leave the system disconnected for at least 60 minutes. This allows time for any self-healing 'polyswitch' fuses to 'heal'. Do not turn on the system before 60 minutes or the fuses will not have time to heal as they will not cool sufficiently.
  4. Re-connect the mains supply.
  5. Switch on the computer and check that no error message is reported. If it is then the computer must have a fault (usually damaged/shorted USB ports).
  6. Insert a known good USB keyboard which has Num Lock, Caps Lock and Scroll Lock LEDs (lights) into the rear USB port (if present).
  7. Switch on the system and observe the USB keyboard LEDs - they should flash indicating that the port has power and the USB data lines are working.
  8. Repeat the switch on test with the USB keyboard on each USB port in turn.
  9. Inspect the USB plug of another USB peripheral (eg mouse) and insert it into another USB port on the computer (you now have a USB keyboard and a USB mouse connected) - repeat the switch on test and check they both work correctly in Windows.
  10. Repeat step 9 until all required peripherals have been connected.

If the BIOS or Windows reports an error during testing, this should help to diagnose the cause of the issue.



Checks

It is very common for the plastic tongue inside USB plugs and sockets to break if misused (eg a USB pen drive is bent upwards or downwards). This can result in the four USB contacts inside a USB socket being exposed and shorting out, either when another USB plug is connected or if the contacts are permanently bent and touching the metal shroud inside the USB socket.



Possible Issues

If several computers to appear to develop the same or similar fault within a few days, this is a good indication that a user may have a faulty USB device.

If a USB port has been damaged, check that none of the four contacts are shorting (eg insert two pieces of double-folded clear adhesive tape above and below the four contacts), test the computer still works correctly and then seal the USB port using tape or by filling it with glue to prevent it's use.



More Information

Warranty and Repair

User damage is not covered by the RM warranty. A damaged front USB port on a PC will require a new front panel PCB. A damaged rear USB port on a PC will require a complete new mainboard. A damaged USB port on a notebook will require the whole notebook mainboard to be replaced.



FEEDBACK
Did the information in this article help answer your question?
 Yes
 No
 Just browsing or article not relevant
Please add any comments about this article in the box below. If you answered No then it is important you tell us why so that we can change the article if required. We can only respond if you log in to the RM Support website or provide your contact details. Note: If you need help with a technical query, please log a call online or telephone our support team.
Thank you for your feedback, which is sent directly to the RM Knowledge team. We address every message received with the intention of improving our Knowledge Library articles. If you have an unresolved technical issue, please contact RM Support.


If this article has not helped provide a solution then it is also possible to log a call...



Document Keywords: error 0701, over current, usb device error


Please read - important disclaimer information.
http://www.rm.com/_RMVirtual/Includes/csredirect.asp?cref=&title=Standard Content Disclaimer


Top Of PageTop of page